Proven clones for the home grower community

By Chris Gaffney

How to Set Up a Clone Propagation Station at Home

A home clone propagation station is usually a tray and humidity dome on a heat mat, under gentle light, with a sensor nearby to watch conditions. It gives fresh cuttings a steady, humid spot while roots form. You can find the clone dome and heat mat options we carry in one place.

This post covers gear and layout. For cutting and rooting technique, see our general cloning practices guide.

ㅤ

🌱 Who Needs a Propagation Station?

A propagation station is most useful if you take your own cuttings, for example from a mother plant. If you are starting with rooted clones, you may not need the full setup; our guide to what to do when your clones arrive covers that first week.

ㅤ

🧰 The Core Gear

Tray and humidity dome

A clear dome over a cell tray holds humidity around cuttings. AC Infinity's kits come in a 5x8 tray (40 cells) and a 6x12 tray (72 cells). Some versions include a height extension for taller cuttings.

Heat mat

A heat mat warms the tray from below. The SUNCORE S3 measures 10 x 20.75 in, is IP67 waterproof and includes its own temperature controller.

Gentle light

Some dome kits include built-in LED bars that give cuttings gentle light.

Clone collars

Foam clone collars hold stems upright in cloners and net pots. AC Infinity makes them in 2, 3 and 4-inch sizes.

A sensor

A temperature and humidity sensor near the dome helps you see whether conditions are steady.

ㅤ

📍 Where the Station Goes

A propagation station can sit on a shelf, in a corner of your veg space or in a small tent. AC Infinity's CLOUDLAB propagation tent is 24 x 24 x 36 in with shelf racks for clones and seedlings, and a 2x2 tent can also work. See our 2x2 grow setup for small-tent options.

ㅤ

🔧 Setting It Up Step by Step

  1. Place the heat mat on a flat, level surface and connect its controller.
  2. Set the tray on the mat and fill the cells with your rooting medium.
  3. Add the dome and check that its vents open and close.
  4. Position the light, either the dome's LED bars or a gentle light above.
  5. Place a sensor near the dome; our sensor placement guide explains where readings are most useful.

ㅤ

🌬️ Venting the Dome and Moving On

As roots develop, many growers open the dome vents gradually so cuttings can adjust to drier air before moving into the main tent. For light guidance in the first week, see our clone light schedule guide.

ㅤ

🧽 Keeping the Station Tidy Between Rounds

Between rounds, empty the tray, wipe the dome and tray, and let everything dry fully before storing it. A clean, dry setup tends to make the next round easier to start.

ㅤ

❓ Frequently Asked Questions

What do I need for a clone propagation station?

A tray and humidity dome, a heat mat, gentle light, clone collars if you use a cloner or net pots, and a sensor to watch conditions.

Do cannabis clones need a humidity dome?

Fresh cuttings have no roots to take up water, so many growers use a dome to keep humidity around them while roots form.

Is a heat mat necessary for clones?

It is not required, but many growers use one to keep the root zone warm and steady, especially in cool rooms.

What kind of light goes over a clone dome?

Gentle light, such as the LED bars built into some dome kits. See our clone light schedule guide for details.

When should the humidity dome come off?

Usually gradually, as roots form. Our general cloning practices guide walks through the timeline.

ㅤ

📚 Continue Learning

ㅤ

🌿 Ready to Fill Your Tent?

Prefer to start with roots already in place? Browse our rooted cannabis clones, then see our clone and propagation gear to match the gear to your space.